Community Conversation => Female to male transsexual talk (FTM) => Transsexual talk => FTM Gear => Topic started by: rexyrex on November 28, 2011, 01:33:27 PM Return to Full Version

Title: i need latex or rubber tubing
Post by: rexyrex on November 28, 2011, 01:33:27 PM
hi i need some more tubing for my stp (as i kinda rip it off, to upgrade the stp) so now i just need a new tubing erm i looked online but i have no idea about sizing and worryed i would order the wrong one. (the hole to small or the wall is to thick)

So can any one give me some good link maybe from UK if possable if not it ok something cheap too......

also what is ID and OD?
Title: Re: i need latex or rubber tubing
Post by: Wesley_33 on November 28, 2011, 02:33:17 PM
ID = inner diameter
OD = outter diameter

Not sure about where in the UK to get it from sorry.
Title: Re: i need latex or rubber tubing
Post by: Nathan90 on November 28, 2011, 03:50:14 PM
I've got no idea where to get it here in the Netherlands so I ended up ordering some off ebay. Can't tell you much about the sizing now though but I just picked one and I'll see how it works out. Just make sure it's not too narrow or it might 'cause your spoon/nipple whatever to overflow. ;)
Title: Re: i need latex or rubber tubing
Post by: NXTransit on November 28, 2011, 03:55:35 PM
The tubing I used was 1/4 in diameter. That's a pretty common size, and the only one they had at my local hardware store. Depending on what you are attaching it to, (i.e I put it on a medicine spoon receptacle) you will probably need lube (and some spare time). However, I just used water.
Title: Re: i need latex or rubber tubing
Post by: rexyrex on November 28, 2011, 04:49:23 PM
Quote from: Nathan90 on November 28, 2011, 03:50:14 PM
I've got no idea where to get it here in the Netherlands so I ended up ordering some off ebay. Can't tell you much about the sizing now though but I just picked one and I'll see how it works out. Just make sure it's not too narrow or it might 'cause your spoon/nipple whatever to overflow. ;)

That what im worryed about.
Quote from: NXTrans on November 28, 2011, 03:55:35 PM
The tubing I used was 1/4 in diameter. That's a pretty common size, and the only one they had at my local hardware store. Depending on what you are attaching it to, (i.e I put it on a medicine spoon receptacle) you will probably need lube (and some spare time). However, I just used water.

im using the whiz freedom...i brought off the site but i couldnt pack with it and it looks like i had a boner! so i had to take it out and remove the bit that was hard (it the smaller end bit which was glued to the bigger hole bit) so it been removed and it much better but now the hole is bigger then it was before, would that common size fit on or would it kinda make it like what Nathan90 said.

i can post pic if it helps

Also i tried the nipple but that didnt work for me :(
Title: Re: i need latex or rubber tubing
Post by: Nathan90 on November 30, 2011, 04:23:10 PM
I got some tubing in the mail today (don't know about sizing, don't feel like measuring and I most definately don't feel like turning the mm in inches), but I figure it might be too stiff. Hah, I put the tubing in the packer (without the nipple end 'cause those are at my other home) and the packer looks rather erect with the tubing. It will fold and stuff, but I'll have to see what it looks like with a harness in my briefs.

Fortunally I have the purple extensiontube that the whizz freedom sells as well. It's too short to use alone, but I might combine it with my new tubing, cause it's thrice and flexible.
Title: Re: i need latex or rubber tubing
Post by: anibioman on November 30, 2011, 05:30:16 PM
ID- inner diameter

OD- outer diameter

you should just find a ruler and think about it. try to get tubing with a small wall thickness so it wont make you look you have a boner.